Car Key Button Repair

A broken car key remote repair key button can be a source of frustration. It is possible to contact a 24-hour locksmith Service for help or purchase a new remote.

You could be able to save money by fixing your old key fob instead of replacing it. This is particularly true if the issue is caused by a worn switch or faulty contact.

Battery

If the buttons on your key fob don't respond to pressing the buttons, that could be a sign that the battery is dying or at the end of its lifespan. Fortunately, replacing the battery is an easy task that can be completed by yourself rather than hiring a locksmith or dealer to complete the task for you.

Locate the battery compartment first. This is usually found on the back of the key fob and could be hidden behind a slide-out cover or an access point that opens when you press a button. Once the compartment has been exposed then look for the small button-cell battery. It's usually shaped as coins and marked with a plus and minus sign. Remove the old battery, and replace it with a brand new one. Make sure that the plus and the minus symbols are properly aligned.

Once the battery is in place close the compartment and snap the two halves of the key fob together. Be sure to align the pieces and snap them into place properly before closing the door and testing your keys. Press any of the buttons to ensure that they work properly.

If your remote keyfob does not work after replacing the battery, there may be other problems that require a different type of repair. Dropping the device into a puddle can cause it to stop functioning. It could also be due to a malfunction with the internal electrical system or need to be deprogrammed. Check out these other common automotive troubleshooting methods to determine if your key repair fob is experiencing a different issue.

Switches

Depending on the year and manufacturer, there are various kinds of switches that are found in the car keyfob. The older style key is equipped with an electronic chip that is visible inside the case. The modern keys function by transmitting signals to your car. The buttons on a key may be worn out or damaged through normal use, regardless of the type. They become difficult to press or ineffective. If you attempt to press the button too hard it could cause further damage, and could even prevent the key from being able to start your vehicle in the future.

If your lock key repair near me doesn't appear to be working, you should first try changing the battery. If this doesn't work, you may have to clean your key's fob or re-adjust its switches. Since these tiny electronic switches are constantly being moved around they are more prone to wear out than larger parts of your key.

The switches are rubber-like and they're coated with an electrically conducting film that is prone to wear out over time. However, they're tiny and cheap to replace. They are soldered onto the circuit board, so you must carefully take them off without damaging other components. Then, you can solder the new ones into and reassemble the fob.

An effective way to protect your car key fob from becoming damaged is to not use it for longer than a couple of hours at a stretch, and to keep it out of the way in areas in areas where it is visible. Also, you should locate a safe place to store your keys when you aren't making use of it.

If you've tried cleaning your key fob and replacing the battery, and the issue continues to persist, it may be the right time to seek out an appointment with a locksmith. A professional locksmith can test the frequency of your key to determine if your vehicle is still able to communicate. They can also open and replace microswitches, change cases, and more.

Outer Case

If the buttons don't move freely in the case, they could get stuck or break. If cleaning the case using rubbing alcohol and a cotton swab fails to work, it might be necessary to remove the case. If the contacts the buttons touch are not a good fit, or if they are damaged, adjusting them could be the only solution.

Rubber buttons can be worn out over time. The rubber is stretched, nails gouge into it, and the buttons become difficult to press. In this scenario, the key may fail, and it's time to replace the case or button. This repair involves removing the remote, then locating the buttons on the circuit board, then heating the solder and carefully removing them. The circuit board then gets soldered with new buttons. The case can then be rebuilt with the horse shoe key blade piece inserted. The new buttons should be snugly fitted into the case to prevent them falling out.

Inner Case

Since your key fob is prone to be tossed around and occasionally be pressed by accident and the buttons within can become stuck or broken over time. Utilizing metal tape and a hole-punch, you can usually solve this issue when your car is away from home when the key fob won't work and you are unable to open the doors, but not start the engine. This simple fix can allow you to safely return to your vehicle to complete your journey.